⏱ 0:00

🎛 Preferences

New programs

Default machine
Default tools

Saving

Playback

Editor

Text size

Code Meerplot writes (Part Designer)

💾 Replace the file?

⬇ Export settings

Saves your tools, macros, default machine, Shop Tools templates and preferences to one file. Open it on another computer with ⚙ Settings → Import settings.

⬆ Import settings?

🖥️ Graphics acceleration looks off

    📐 Starters

    Update Meerplot?

    💬 Feedback

    Ideas, bugs, anything that’s confusing – it goes straight to Meer.

    Pictures up to 6 – screenshots help a lot (you can also paste one with Ctrl+V)

    Program changed on disk

    Stock & Machine

    Machine & workholding

    Machine / stock type
    Each one is drawn and checked for crashes when it is on. Their sizes are below.

    Stock

    Use a part stock
    Off = only draw the tool path (no bar, no material checks)
    What kind of part?
    Only the sizes that part needs are shown
    Stock diameter (OD)
    Bore / hole (ID)
    Head recessed – Ø (0 = flush)
    The open pocket in front of a head welded in recessed
    Recess depth (Z0 face to the head)
    Journals
    Ø × length from Z0, smallest first – e.g. 1.165x2.75, 1.528x4
    Journals on
    Radius into the body
    at the journal next to the head – never a sharp 90°
    Recess on
    Stock length (from Z0 face)
    Workshift – End A
    Raw stock sticking out past Z0 on the first end – faced off to length
    Workshift – End B (flipped)
    Raw stock past Z0 on the other end, after the part is turned around
    Stock height (Z, top = 0)

    Chuck jaws

    Show the chuck & jaws and check them for crashes
    Grip length (how much of the part is inside the jaws)
    Measured from the jaw face back along the part – nothing can be cut in this zone
    Jaw length (along Z)
    Jaw height above the stock
    Chuck body diameter

    Home position (G28)

    Home X (diameter)
    Home Y
    Home Z

    The tool starts at home. G28 sends the named axes (X/U, Y, Z/W) home, passing through any point you give; a bare G28 sends all axes.

    Steady rest

    Steady rest
    “When the program says” = closes on comments like (CLOSE STEADY REST), opens on (OPEN STEADY REST)
    Distance from Z0 face to the rest (center)
    Rest width (along Z)
    Rest height above the part
    Arc direction (G2 / G3)

    Crash detection & travel limits

    Check for crashes
    Max X travel (diameter)
    Min Z travel
    Max Z travel

    Cycle time estimate

    Rapid traverse rate
    Max spindle speedRPM
    Tool change timeseconds

    Tool Manager

    T0404 = tool 4, offset 4. The Offset box starts out the same as the tool number – change it if a tool uses another offset. Tools with a full code, like 303 and 313 (both in station 3), are kept apart. Tools used by the program are added automatically. The nose radius is drawn at the tool tip.

    🔷 Insert guide

    📂 Macros

    💾 Backup & Restore

    One file with everything: settings, open tabs, macros, Tool Manager and stock defaults, Excel templates. Keep a copy on a USB stick or the shop drive – it also moves your setup to another computer.

    Measuring a center drill

    Pilot Ø Pilot length 60° countersink Body Ø

    Stick-out doesn’t matter for a center drill – Z0 is taught with the tool before you start.

    Center hole size by part weight

    A = countersink Ø at the face (60°), B = pilot Ø. “Tip depth” is how far past Z0 (the face) a standard center drill goes for that A – Meerplot notes it under Problems when a program goes noticeably shallower or deeper.

    What is stick-out?

    Boring bar part (cut away)bore holder / turret blockboring bar STICK-OUT insert tipface of the holder Bar Ø Drill / tap collet / holder STICK-OUT (to the drill point)

    Stick-out is how far the tool reaches out of its holder: measure from the face of the holder (where the bar or drill comes out of the clamp, collet or sleeve) to the cutting tip of the insert – or to the point of the drill / tap.

    Apply this fix?

    Before

    After

    Calculator

    Taper helper

    Code Library

    ⚙ My machine’s codes – add or rename M-codes your machine builder uses

    Speeds, Feeds & Surface Finish

    Compare programs

    A (left):
    B (right):

    How to use G-Code Backplot

    Keyboard (after clicking the graph)

    ↑ ↓Previous / next line of G-code (the graph follows)
    ← →Step one move back / forward
    SpacePlay / pause
    Home EndStart / end of the program
    Ctrl+Z / YUndo / redo (in the editor)

    🔢 Renumber N blocks

    What to do
    Start at
    Step
    Comment lines, % and O program numbers are skipped. G70–G73 P/Q, M97 P and GOTO numbers are changed to match, and “Remove” keeps any N those still need.

    ↔ Shift / Mirror

    Do
    Axis
    Move by
    Lines

    🖨 Setup Sheet

    Insert a Radius or Chamfer

    Start point (filled with where the tool is at the cursor line)

    End point

    Radius

    
     

    Meerplot™ G-code backplot & simulator

    v3.55.0

    Created by Meer Rasheed. © 2026 All rights reserved.

    Simulation is a guide only – always prove out new programs on the machine with care (single block, reduced rapid, feed hold ready).

    What’s new

    📋 Program Templates

    Your Excel G-code sheets – fill in the sizes, get the program.
    Program preview

    Close program?

    ✏️ Part Designer beta

    Keys: V select · L line · R shape · A arc · K corner · X const. line · T tangent · D delete · Esc stop · wheel zoom · right-drag pan

    📐 Blueprint → Part beta

    Import a drawing, enter the part's diameters, lengths, chamfers and radii, then see it on the graph or make the G-code.
    📄
    Drop a PDF or picture of the drawing here
    or click Import PDF or picture.
    PDFs exported from CAD let you click the dimensions to use them. Scans and photos are shown so you can read them while you type.

    Dimensions found on the drawing

    No drawing loaded yet.

    Finished part – outside profile, from the face (Z0) toward the chuck